Combustible Gas Detector: Statox 501 Infratox

Statox 501 Infratox detects gases in the LEL and ppm range.

Protecting people and assets from hydrocarbons

The infrared absorption method of gas detection is ideal to detect hydrocarbons such as fuels. It features enough sensitivity to expand the range of application into the ppm range. For instance fuels such as gasoline, diesel or kerosene are mixtures of hydrocarbons.

Infrared gas detection theory of operation

Some gases absorb light at a certain wavelength (colour). This absorption band is specific to the gas. The rate of the absorption depends not only on the substance to be detected but also on the number of gas molecules (i.e. the concentration of the gas). This premise is used to detect gases. For example, the C - H bond in hydrocarbon molecules will oscillate and absorb light at 3, 4 mm. This fact makes it so easy to detect fuels. Hexane, for instance has 14 C - H bonds compared to Methane which has only 4!

A light beam is directed through a cuvette filled with the gas to be detected. The more hydrocarbons are present, the more light will be absorbed. A photo detector at the other end of the cuvette measures the remaining light intensity. The difference between the original and remaining light intensity corresponds to the gas concentration.

A reference beam with a different wavelength compensates for potential interferences of dust, humidity or variations of intensity from the light source.

Fail-safe technology

Failure of important components such as the light source or photo detector will trigger a "system fail" alarm. Most local authorities will accept this as a self-diagnostic feature. Systems including a self-check require less maintenance and calibration, saving time and money.

Simple maintenance: Easy to read display and non-Vintrusive calibration

The bright LED display of the Statox 501 Infratox shows the gas concentration in percent L.E.L. (Lower Explosion Limit). An important accessory is the calibration adapter, featuring control buttons operating Hall-sensors inside the Ex d housing.
The service menu is password protected preventing unauthorised access. All parameters can be checked and changed, or a calibration can be done all without opening the transmitter. The adapter is also equipped with a gas outlet so that it can be used for flow-through applications.

Impervious compact design

The dimensions of the Statox 501 Infratox are small and compact. The sensor compartment is completely sealed, not allowing dust or insects to enter. It is located in the center of the sensor head. This allows heat radiation from the electronics and the infrared lamp to keep the unit a few degrees above the ambient temperature thus avoiding condensation. This innovative design makes any additional heating unnecessary, allowing the sensor head to be very energy efficient. This saves additional money by eliminating more expensive wiring and a bigger power supply that would otherwise be necessary.

The sensor head is rated protection class IP 67 (6 = protection even against fine dust, 7 = submerged 1 m deep in water for 30 minutes). You can have confidence that this system will safely operate even in the harshest environment.

 

 Technical Data  
 Detectable gases  combustible gases and vapors
 Measuring range  0 – 100 % L.E.L. 0 - 5% or 0 - 2% CO2
 Measuring principle  Infrared absoption, NDIR 2-channel
 Detection limit  3 % L.E.L. Methane 200 ppm CO2
 Response time  t50 < 10 s, t90 < 25 s
 Accuracy (Full Scale)  ± 2% L.E.L. at room temperature
 Warm up time  20 s, full specifications after 30 min
 Operating temperature  -20 °C to + 60°C (- 4°F to + 112°F)
 Storage temperature  -20 °C to + 60°C ( - 4°F to + 140°F)
 Humidity  0 – 99 % r. H.
 Pressure  800 – 1100 hPa, < ± 0,1 %L.E.L. / hPa
 Power supply  24 V DC (18 – 29 V DC) / 1 W
 Current  24 V DC (18 – 29 V DC) / 1 W
 Connection  4 Wire
 Output  4 – 20 mA, electrically isolated, max. load 220 O
 in the service mode 2 or 4 mA programmable,
 system fail 0 mA
 Display  LED three digits
 Dimensions  Height: 150 mm Width: 120 mm Depth: 120 mm
 Weight  app. 3,1 kg 6,8 pounds
 Material  stainless steel, fiber reinforced polyamide
 Protection class  IP 67 (NEMA 4 and 6)
 Ex-Approval ATEX Standard  II 2 G EEx de IIC T5
 Approval #  BVS 04 ATEX E 006 X